Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the tons is stable and trustworthy.
4. The start has to be slow and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed doglegs will cause the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The tons will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will Electric Forklift Truck for Warehouse be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead slightly when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must discharge the goods or lower the fork framework.
2. Pull the emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, examine whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven backwards when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or hefty goods and most likely to the driver's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by passing on the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It Stand-on Electric Pallet Stacker is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking force to exile round or easy-to-roll things.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the opposite side of the area with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844